STOP and read! Test before installing
STOP and read! Test before installing
1.Please unpack the range hood and accessories carefully.
2.Remove the baffle filters, check any dent or damage inside and outside.
3.If found any loosing parts, please remove them.
4.Place the range hood on a flat stable surface, plug in 120V AC power source. Press the power button and the speed buttons to turn on.
5.Check if any unusual metal touching noise, check the speed variation,and press the Light button to check the lights.
6.Follow the steps below to check all functions.
Control Panel Layout and Buttons Configurations:
6.1 From left to right side: Lighting Key (K1), Timer Key (K2), LED Display, SpeedKey(K3),Power Key(K4)
When the power supply connected, all indicate lighting is On and then Off in 1second. To press K4 to open the hood.
6.2 When the hood is On, to press K3 to open Fan Speed 1 , to press again toopen Fan Speed 2", as so forth, to open Fan Speed 3" and 4" by K3. The FanSpeedis changed as 1-2-3-4-0-1-2-3-4.
6.3 lf there was any fan speed working, to press K2 to open Timer Mode, thedefault is 3 minutes and do count-down step. Or to press K2 or K3 to set thetimer as wanted, the maximum timer is 15 minutes.
6.4 To press K1 to open or close the lamp. The luminance of lighting can beadjusted from 0% to 100% as wanted by touching K1.
6.5 Gesture Control: to move your hand from left side to right side to open 1* FanSpeed.And again to open 2 Fan Speed, and 3", and 4".On the contrary, to move your hand from right side to left to reduce the speed level.
Please Note: when using gesture control function, please make sure to move yourhand from 2 signal ports completely.
Optional
This hood switch control can be operated by remote controller if wanted.
7.Refer to the TROUBLESHOOTING section if a fault has been found.
8.The plastic protective film was removed for sanding polish finishing.
Important safety instructions
-PLEASE READ THIS SECTION CAREFULLY BEFOREINSTALLATION
⚠️WARNING: TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURYOBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with allapplicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidderutilities
3) Ducted fans must be vented to the outside。
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICEPANEL
b) Clean all grease-laden surfaces frequently. To reduce the risk of fire and to disperse properlymake sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl spacesor garages.
NOTE
- This warranty is invalid without an authorized agent's receipt or if unit is damaged due to misuse, poor installation, improper use, mistreatment.negligence or any other circumstances beyond the control of IKTCHRANGE HOODS authorized agents. Any repair carried out without thesupervision of IKTCH RANGE HOODS authorized agents wilautomatically void the warranty
- IKTCH RANGE HOODS will not be held responsible for any damages topersonal property or real estate or any bodily injuries whether causeddirectlv or indirectlv bv the range hood
⚠️WARNING: TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE TOP GREASE FIRE:
1. Keep all fan. baffle/spacer/filter/oil tunnel/oil container and arease-laden surfaces clean. Greaseshould not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.
2. Alwavs turn hood ON when cookinge
3. Use high settings on cooking range ONLY when necessary.
4. Do not leave cooking range unattended when cooking.
5.Always use cookware and utensils appropriate for the type and amount of food prepared.
6. Use this unit only in the manner intended by the manufacturer.
7. Before servicing, switch power off at service panel and lock service panel (if possible) to preventpower from switching on accidentally.
8. Clean ventilating fan frequently.
What to Do In The Event Of a Range Top Grease Fire
❎SMOTHER FLAMES with a tight fiting lid, cookie sheet, or metal tray, and then turn off the burner.KEEP FLAMMABLE OR COMBUSTIBLE MAERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.
❎NEVER PICK UP A BURNING PAN -You May Get Burned.
❎DO NOT USE WATERincludin wet dishcloths or towels - a violent steam blast will result.
❎Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to DOIf You Smell Gas
❎Extinguish any open flame.
❎Do not try to turn on the lights or any type of appliance.
❎Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away.
⚠️CAUTION
1. For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustior and exhausting of gases through the flue (chimney) to prevent back drafting.
3. Follow the heating equipment manufacturer's guideline and safety standards such as those publishedby the National Fire Protection Association (NFPA), and the American Society for Heating.Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4. Turning any switch on may cause ignition or an explosion.
5. Due to the size and weight of this hood, two people installation is recommended
![]() |
ELECTRICAL SHOCK HAZARD - Can result in serious injury or death. Disconnect appliance from electric power before servicing.If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local,State, and Federal Codes. |
Start the installation
1) Installation planning
- Measure the distance between stove top and the bottom of range hood. A distance of 27” to 30” is recommended. Minimum 25.5" is required for safety concern.
- Decide the venting method and the location of the venting pipe from the hood to the outside.
- Purchase any necessary accessories from a hardware store, such as duct, elbow, reducer, damper, duct tape, screws, etc.
- Find and mark the stud locations using a stud finder to plan the mounting locations finnl
2) Measure the top vent and the power cord positions, cut the openings (slightly larger for easy accessible) fbr hood exhaust and power cord under the cabinet.
3) For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on each side.
4) Puncture the knockout screw holes on the top for screw mounting under the cabinet.
5) Mount this range hood under the cabinet, 2 people are required for this installation.
- Draw power cord through cabinet access opening and center the hood beneath the cabinet.
- From inside of the hood, place screws into the exact center of each knockout hole and secure to cabinet bottom. Finish tightening all screws until secure.
CAUTION: Make sure the range hood is secure before releasing!
- For safety purpose, mount the screws through the pre-drilled mounting holes or/and drill new holes from inside the back of the hood to the studs or lumbers. For a more secure installation, use as many mounting holes as needed to secure from the inside of hood.
6) Use 6" round metal duct (or semi-rigid aluminum duct, follow building codes in your area) to connect the exhaust on the hood to the duct-work above. Use foil tape or duct tape to make all joints secure and air tight.
7) Connect the power cord to a designated grounded standard 110V outlet.
- Or cut off the plug and connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to colors (i.e. black to black, white to white, and green to green). Store excess wires in the wiring box.
8) Install baffle filters and stainless spacer if any.
9) Turn power ON in control panel. Check all lights and fan operations.